Product Code: ANTI-AIRLOCK ADAPTER
JORC Industrial Anti-Airlock Adapter The anti-airlock adapter is simple to install and helps prevent air locks from being created. This adapter is typically applied in combination with the MAGY but can also be connected to other level sensed condensate drains. The anti-airlock adapter has a 1/2 inch inlet and outlet. Features Ensuring the installation is carried our correctly, the anti-airlock...
Product Code: Ball Valve Strainers
JORC Industrial Ball Valve Strainers The FLUIDRAIN and EZ-1 drain valves have an orifice of 4.5 mm (EZ-1 4.0 mm). This large orifice ensures that emulsions and particles in compressed air cannot block the valve. We supply 1/2 inch, 3/8 inch and 1/4 inch valves and to avoid unnecessary adapters etc. we offer the right strainer for the right valve. The incorporated shut off valve supports...
Product Code: Drain Heater
JORC Industrial Drain Heater Anti-Freezing Device In very cold temperatures, condensate may run the risk of freezing when it does not continuously flow through the system. The DRAIN HEATER guarantees a continuous condensate flow in all systems where you have trouble keeping the condensate flowing due to extreme cold weathers. The DRAIN HEATER can be installed on the KAPTIV-CS, MAGY and...
Product Code: DRAIN HEATER T-ADAPTER
JORC Industrial Drain Heater T-Adapter The T-adapter is simple to install and enables you to connect the DRAIN HEATER to various 1/2 inch drains. The DRAIN HEATER is an anti-freezing device that prevents drains from freezing in extremely cold conditions. The DRAIN HEATER with T-adapter can be applied in combination with both level sensed drains and timer controlled drains. The T-adapter is made...
Product Code: IP Coil Sealing Set
JORC Industrial IP Coil Sealing Set A solenoid valve is a very versatile product. Its simplicity and quick open/close time make it ideally suited for numerous applications. Some of these applications require extra protection of the solenoid to avoid water accumulating between the solenoid and the valve shaft. For these applications we have an extra sealing set which helps to eliminate the...
Product Code: Mounting Brackets
JORC Industrial Mounting Brackets Mounting brackets allow easy installation of condensate drains and small oil/water separators to walls, on the floor or inside of refrigerated dryers. Particularly high pressure compressors generate lots of vibrations. In applications like these it is wise to fix drains adjacent to the compressor. The JORC mounting brackets offer the suitable solution for these...
Product Code: Multi-Inlet Adapter
JORC Industrial Multi-Inlet Adapter The SEPREMIUM 5 - 60 models offer two inlet options. By applying the inlet adapters you can increase the inlet options to six inlets. This is a great tool to simplify the installation of JORC's oil/water separators. The Multi-Inlet adapter allows for up to three additional condensate inlet options. The brass adapter threads in to the brass inlet of our...
Product Code: PLATTO
JORC Industrial PLATTO Condensate Drip Tray When oil water separators are being serviced, it is important that condensate does not contaminate your customer's factory floor or compressor room. The PLATTO ensures that you customer's compressor room stays clean and no unnecessary pollution occurs. Oil water separators sometimes get disconnected and wheeled away to be serviced. By installing the...
Product Code: Connectors
JORC Industrial Power Connectors Power (DIN) connectors are available in FORM A and B (square and rectangle), with or without a moulded power cord. Special adapters, to take connection from FORM B to FORM A, are also available. Features Optionally available with moulded cable, offering time saving during installation DIN form A and B available With or without moulded cable available
Product Code: Remote Switching Kit
JORC Industrial Remote Switching Kit A typical compressed air system has air loss through pipe work connections, leaking float type drains etc. At the end of the working shift the AIR-SAVER will shut the air tank off from the rest of the system. The content of the compressed air tank will be saved, rather than lost through pipe work leakages. The REMOTE SWITCHING KIT allows you to control the...
Product Code: SERVICE KITS Routine Maintenan
JORC Industrial SERVICE KITS Routine Maintenance Products Great care is taken to ensure long lasting components are selected and applied in our products. JORC products are designed in a way that makes servicing simple, quick and error free. Servicing JORC products is a cost effective way to recondition the products for many more years of draining service. Features High quality seals are...
Product Code: Side Inlet Adapter
JORC Industrial Side Inlet Adapter A specially designed adapter is available to offer a side inlet option for the KAPTIV-MD zero air loss drain. The KAPTIV-MD fitted with the specially designed adapter offers an inlet height of only 83 mm! This is particularly interesting for installing the KAPTIV-MD inside refrigerated dryers. Also, piston type air compressors can be fitted with the reliable...
Product Code: SOLENOID COILS
JORC Industrial Solenoid Coils JORC's JC-type coils are produced with H-grade coil insulation, ensuring maximum heat resistance during operation. The outer encapsulation is an ABS type material. All voltages are available ranging from 12 - 380 VAC/DC 50/60 Hz. There are three coil sizes (JCS, JCM and JCL), depending on type of valve in combination with pressure rating requirements. Features...
Product Code: Solenoid Valves
JORC Industrial Solenoid Valves A wide range of solenoid valves are offered in a 2/2 way and 3/2 way configuration. Options include direct acting and diapraghm type operation in a Normally Open or Normally closed version. Explosion proof coils are available and are encapsulated in special epoxide resin. Features All seals available for any application H grade coil insulation ABS coil...
