The 30 series power units are an entry level system utilizing a 10-4, 10-5 or 10-6 pump mounted on a base plate with an filter regulator lubricator (FRL) assembly, muffler, high pressure manifold, manual release valve and fluid pressure gauge (optional on units 30,000 psig and higher).

With a small footprint (12" x 12") this unit is ideally suited for applications with limited space. User need only supply an air line, fluid inlet and fluid outlet lines for system to operate.

Click here for Technical Data

The 40 series power units utilize the same basic components as the 30 series and mount them on a larger baseplate (largest is 28" x 12 1/2") which can accommodate an optional reservoir - 2, 3 or 5 gallons. Best suited for applications not requiring large amounts of fluid, pressure testing, clamping and holding etc.

Units need only an air supply line and fluid pressure line for system to operate.

Click here for Technical Data

The 50 series power units are self contained high low systems. Using either a 10-5 or 10-6 series pump and a 3 gallon pressurized reservoir the unit will provide low pressure high flow oil for rapid initial actuation (cylinder extension). The unit senses increased back pressure and automatically starts the pump that will bring fluid pressure to required level. The pump will stall and hold at selected pressure until operation is completed.

The 50 series units were designed to save operating and maintenance costs which combined with the SC pumps ability to hold pressure and not require any energy, all add up to an economical and environmentally friendly solution for hydraulic power.

Click here for Technical Data

The 60 series power units incorporate either the 10-5 or 10-6 series pump an FRL assembly, high pressure plumbing, manual release valve and fluid pressure gauge (30,000 psig and higher optional) all mounted on top of a 5 or 10 gallon stainless Steel reservoir.

These units combine all of the features on our 40 series with only a 14" x 14" footprint allowing a lot of hydraulic power in a space conserving package.

Click here for Technical Data

The S10016 series power units incorporate the 10-4 series pump, 2.2 gallon reservoir, air supply filter/regulator and shut off valve, high pressure plumbing and panel mounted fluid pressure gauge into a rugged portable tubular frame.

You get the same features of the 40 series unit built into a protective frame facilitating easy portability without the concern of component damage. Excellent for bolt tensioning, torque wrenches or any industrial facilities with multiple end uses. The S10016 unit lets you bring high pressure hydraulic power to the job, simple to use just connect the existing plant air supply to the unit and up to 22,000 psig hydraulic pressure is at your disposal.

Click here for Technical Data

The S10017 series power units incorporate a 10-5 series pump, 2.5 gallon reservoir, high pressure plumbing, panel mounted fluid pressure gauge (optional if pump rating exceeds 30,000 psig) into a tubular frame that is larger than our S10016 series.

The S10017 units have been standard issue for the bolt tensioning industry and are widely used by rental facilities. The components are protected, easy to inspect and service facilitating rapid turn around times and minimal downtime.

Click here for Technical Data

The S10018 series power units incorporate the 10-6 pump into a tubular frame utilizing the same components as our S10017 series.

This gives the user all of the features we build into our other power units along with the increased fluid flow and pressure capabilities of the 10-6 series pumps. With the ruggedness and portability of the protective frame we can offer fluid pressures up to 73,000 psig that can be quickly and easily transported (weighs 40 lbs complete) supplied with existing shop air and put into service.

Click here for Technical Data

The S10304 series power unit packages the ABL-4 compact 4:1 ratio air booster, air filter/regulator and shut off valve a 2.5 gallon receiver and all necessary plumbing together as a turnkey system. All components are mounted to a steel plate with a base for system portability. Just connect a supply line from your existing plant air and run the pressure line from the receiver outlet to the end use and the system is fully operational. This unit provides up to 600 psig air pressure stored in a 2.5 gallon receiver for any end use needing minimal flow and more pressure than your compressor can supply.

Click here for Technical Data

The S10300 series power unit incorporates the ABD-2 double acting 2:1 ratio air booster, 15 gallon ASME 250 psig receiver and all necessary components and plumbing onto a heavy duty skid. This unit when connected to plant air supply will double the pressure and store it in the 15 gallon receiver.

Any end use that requires more pressure than your compressor supplies and does not need high air flow will benefit from the 2:1 system.

Click here for Technical Data

The S10301 series power unit uses our ABD-5 double acting 5:1 ratio air booster and a 600 psig ASME 5 gallon receiver. The system will increase your existing shop air to 5 times the pressure supplied by your compressor, the boosted air is stored in a 5 gallon receiver for end uses requiring up to 600 psig. All components needed to control air pressures both going into and coming from the unit are supplied along with gauges for precise control.

Click here for  Technical Data