icon-product

Valves


Series F Carbon Steel Flanged End Connection 600# 2-4 inch

Series F Carbon Steel 2-4
  • Lever Operated Ball Valve
  • ANSI Class 600 (1480 PSI WP)
  • 2″ Through 4″
  • Bolted Body Construction

  Download PDF

Back to top


Series BLSFD – Fires Safe Double Acting

Series BLSFD - 316SS Fire Safe, Double Acting
  • 15mm to 300mm
  • 316 Stainless Steel
  • Reinforced Carbon PTFE
  • 150 pound
  • -20ºC to 180ºC
  • Double Acting Pneumatic

Fire Safe AP1607 6th E. Cert. No 218781

 

Back to top


CVC Series Velocity Check Valve

CVC Series Velocity Check Valve

6,000 psi [Pn 408] Rated 10,000 psi [Pn 680] Rated

The CVC Series Velocity Check Valve is used on Flow lines to prevent loss of media caused by burst hoses or failed connections. The Soft seal allows bubble tight closing and prevents reverse flow in circuits. This valve includes low pressure differential to effect seal, Stainless Steel spring for long life, Large bore for improved flow through the valve, a choice of thread forms and Versatile design for Male/Female or compression ends.colson-x-cel-logo[1]

  Download PDF

Back to top


Air Operated Directional Control and Release Valves

valve_release_1

These directional control valves are basically family with common characteristics and benefits.

  • They are seated poppet or ball design for virtually zero leakage at high pressures with low viscosity fluids. They are not “bubble-tight’’ on gas. Note: Normally open models will generally hold a tighter seal on low viscosity liquid or gas because seating force does not depend on inlet pressure.
  • They are directly air-actuated for ideal system compatibility in wet or hazardous areas, or when used in air driven pumps or boosters. Yet, if electronic or electrical control is preferred, they can be actuated with any of the wide selection of sub-miniature 3-way solenoid air valves available from many manufacturers.
  • They employ the same basic area ratio principle used in Haskel pumps enabling high forces to be easily and directly controlled from low pressure plant main or instrument air.
  • Although not normally considered for pressure control, all of the normally open 2-way models can do double-duty in a circuit by also providing a safety relief function simply by installing a small air regulator in their pilot line.logo-haskel[1]

  Download PDF

Back to top


Series BLFE – 316 SS Flanged, Electric

series blfe
  • 15mm to 300mm
  • 316 Stainless Steel
  • Reinforced PTFE
  • 20 BAR @ ambient
  • -20º to 180ºC
  • Electric Actuation

Back to top


BH Series BALL VALVES

BH Series ball valve
1,000 psi [Pn 69] Rated 6,000 psi [Pn 414] Rated
  • Robust HIGH pressure design
  •  Internally loaded blow-out proof stem
  •  Floating ball for positive shut off
  •  LOW operating torque
  •  Smooth 1/4 turn action
  •  Flexible 3 piece design
  •  316 ss to NACE specification
  •  Wide range of end connections
  •  Replaceable vlseats & seals
  •  Ease of maintenance
  •  Full material traceability
  •  Choice of lever or pointer handles
  •  Panel mounting option
  • Can be easily actuated
  •  Locking kit available

For Technical Data on Colson Ball Valves, Click here. For Colson Ball Valve Options, Click here.

  Download PDF

Back to top


Wafer Check Valves Carbon Steel 150# 2″ to 6″ Thin

scvWCarbonSteel thinpat ANSI 150 2T6

Thin Pattern Swing Check Valve
ANSI 150 (285 psi WP)
2″ Through 6″
Forged Steel Body Construction
Replaceable Seat Disc Cartridge
Seal Located in Seat, Thus Protected From Flow
NACE Standard
316 Stainless Steel Disc Standard
Generally Larger Port Sizes Than Other Brandslogo_micro_valves_balon[1]

  Download PDF

Back to top


Inline Check Valves

inline check valves

The CV series inline check valves are available in four port sizes from 1/4″ NPT to 1″ NPT and are rated up to 15,000 psig working pressure. Constructed of Stainless steel for use with water as well as most industrial fluids.

The CV series check valve is a simple and effective component allowing fluid to flow in one direction only.sc-hydraulic-L12627[1]

  Download PDF

Back to top


Series BLHPE – High Pressure Electric

Series BLHPE - High Pressure Electric
  • 1/4″ to 2″ BSP
  • 316 Stainless Steel
  • Delrin Seat
  • 200 BAR
  • Ambient
  • Electric Actuationies blhpe

Back to top


Block and Bleed Needle Valves

Block and Bleed Needle Valves

Parker Autoclave Engineers series MVBB block and bleed valve is a two stem manifold valve providing an economical and convenient method of blocking, bleed-ing and calibrating pressure transmitters and gauges. The valve utilizes the mini valve packing and stem design making it compact and easy to use. The valve can be surface or panel mounted for safe operation. In addition, manifold style valves reduce the number of fittings and space required for installation.autoclave-engineers-logo[1]

  Download PDF

Back to top


Safety Relief Valve (L.P) TS25, TS37, TS50, TS100

Safety Relief Valve T Type
  • Pressure equipment directive (PED) 97/23/EC approved
  • Stainless steel (316 / 1.4404)
  • Suitable for liquid or gas use
  • All dimensions in inches
  • It is NOT recommended to operate this valve below 10 psi (0.7 bar)
  • Stated pressure is maximum setting.  Lower settings are available by using a range of different springs.  Please confirm when ordering
  • Leaktight when 90% of “set pressure” is applied
  • Re-seating within 7.5% of “cracking pressure” (pre-set cracking pressure is optional) state details when ordering
  • Recommended MAXIMUM back pressure 145 psi (10 bar)382666[1]

  Download PDF

Back to top


2-Way Ball Valves

2wayballvalve

Autoclave Engineers 2 way ball valves to 20,000 psi. A one-piece, trunnion mounted style, stem design eliminates shear failure and reduces the effects of side loading found in two piece designs. The valves come with re-torqueable seat glands for longer seat life. The PEEK seats offer excellent resistance to chemicals, heat, and wear/abrasion. Included are a full-port flow path which minimizes pressure drop and a low friction pressure assisted graphite filled PTFE stem seal that increases cycle life and reduces operating torque. The valves include 316 cold worked stainless steel construction and viton o-rings for operation from 0°F (-17.8°C) to 400°F (204°C).

autoclave-engineers-logo[1]

  Download PDF

Back to top