L10 Series Double Acting Liquid Pumps
The L10 Series Double Acting Liquid Pump is the largest liquid pump currently manufactured by SC with a 10″ diameter air cylinder, this double acting liquid pump is available in 4 ratios, the highest of which is capable of hydraulic pressures up to 20,000 psig.
Created primarily for the offshore rental tool market, the L10 series pumps are commonly used for subsea valve actuation, wireline control systems, blow out preventor controls and flushing rigs. L10 pumps can be applied anywhere there is a requirement for very high hydraulic pressures along with higher flows achieved by the 10-6 series.
L10 Series Double Acting Liquid Pump in a system
The L10 is a big pump! We have used them several times in custom systems needing large flows. Have a look at our Manufacturing page to see our capabilities or go to the Systems tab of the Products for standard systems.
10-4 Series Liquid Pumps
The 10-4 Series Liquid Pumps are the smallest of the SC “Standard” type pumps with a 4″ diameter air cylinder and 1 1/4″ stroke. Nine ratios available with the highest ratio capable of hydraulic pressures up to 22,000 psig. Commonly used where fluid flow is not critical. Typical applications include proof and burst testing, clamping, pressing, jacks and any end use requiring very high pressure at low flows.
L3 and L3C Series Liquid Pumps
Compact air operated L3 and L3C Series Liquid Pumps. Wetted sections available in 316L Stainless Steel (L3) and Carbon Steel (L3C). Seven ratios available in each material, capable of pressure exceeding 18,000 psig.
Compact pumps are used commonly for jacks, punches, clamping, holding, bolt tensioning, presses, torque wrenches, valve actuation and pressure testing. These pumps are suited for use with de-ionized water, NOS and CO2 applications. Several modifications available including Hand pump attachment and remote pilot options.
L3 and L3C Series Liquid Pumps built in to a Test Unit
These pumps fit perfectly in to the Trident 101 Series Test Unit
10-5 Series Liquid Pumps
The 10-5 Series Liquid Pump and D-5 Series Non Lubricated Liquid Pumps, the original and most common SC “standard” series pump with a 5 1/4″ diameter air cylinder and 1 1/4″ stroke. 16 ratios available with the highest ratio capable of hydraulic pressures up to 55,000 psig. Commonly used for bolt tensioning, filter presses, clamping, proof and burst testing, metal forming. The 10-5 series with it’s many ratios and modification options can be utilized anywhere a source of hydraulic pressure is required. The D-5 series has all the same characteristic including a Non Lubricated feature.
10-5 Series Liquid Pump built in to a Pressure Test Unit
The 10-5 or D-5 from SC Hydraulic is the most popular pump we sell in the Trident 101 Series Pressure Test Unit
10-6 Series Liquid Pumps
The 10-6 Series Liquid Pumps or D-6 Series Non Lubricated Liquid PumpsThe largest of the SC “standard” series pumps with a 7″ diameter air cylinder and a 2 1/2″ stroke. 13 ratios available with the highest ratio capable of hydraulic pressures up to 73,000 psig. Commonly used where very high pressures are required at low flows. Applications include proof and burst testing to extreme high pressures, torque wrench actuation, bolt tensioning, aircraft jacks, filter presses, clamping, holding, metal forming. 10-6 is used extensively by offshore oil companies in many applications due to the pumps inherent ruggedness and reliability. The D-6 has the same characteristics including a Non Lubricated feature.
10-6 Series Liquid Pumps installed in a Pressure Test Unit
We would put this series of pump in to the Trident 101 Series frame and it would make a very economical high flow Pressure Test Unit.